Cisco has released security response acknowledging that the IPS software does not properly handle a rarely used Unicode encoding. Reading the security notice you might be left wondering what's going on. Here's the whole story.

Within an URI (web address), the ASCII characters can be encoded in one of three ways:

• Unless they are reserved, they can be included in the URI directly (for example, you can always use the letter a in an URI).
• You can always escape a character using its hexadecimal value. Letter a can thus be written as %61.
• Unicode character set includes full-width form of ASCII characters, where letter a can be encoded as a two-byte value 0xFF61 (or %ff%61 in an URI)

The IPS software (standalone or integrated in Cisco IOS) does not recognize the sequence %ff%61 as letter a. It's thus possible to evade some IPS triggers by replacing ASCII characters with their full-width Unicode encoding.

The Split DNS functionality introduced in IOS release 12.4(9)T has survived a single maintenance cycle before being broken. While you can still configure the DNS views in 12.4(11)T2 (and they still work), the view names are missing from the router-generated configuration (show running, for example), making the configuration syntactically incorrect. The router will thus reboot without DNS views after you've saved the running configuration to NVRAM.

One of my readers asked an interesting question: „why do the commands executed within a EEM Tcl policy fail with Command authorization fails message?“ The short answer is simple: If you use AAA command authorization (which you can only do if you're using a TACACS+ server), you have to specify the username under which the EEM will execute its CLI commands with the event manager session cli username user configuration command.

In a previous post, I've described how you could generate a (almost) continuous ping from a router using the extended ping command. While that approach is extremely simple to implement, it ties up a line (and if you're working from the console, it's highly impractical). You could get the same results (as Tom has already pointed out) using IP SLA feature of Cisco IOS. Configure the ping request with commands similar to these:

Whenever a router running CEF switching has LAN interfaces (or any other multi-access interfaces), you'll find cached adjacencies for active directly attached IP neighbors in its CEF table. These adjacencies ensure the smooth traffic flow toward the LAN-attached next-hops (preventing the initial packet drop symptom once the next-hop becomes active).

One of my readers made an interesting observation when faced with configuring zone-based firewall on Cisco IOS: „My main issue is a confusion between when to use self and when to use in/outside.“

The rules are simple:

During network troubleshooting or proof-of-concept testing, I often change the state of a loopback interface (to insert or remove an IP prefix from the routing protocols) or flap it to test the impact on network stability. The traditional approach to this procedure should be known to everyone:

Before trying to write Tcl procedures to be executed by Cisco IOS tclsh command, read the following articles:

• Running Tcl procedures from IOS command line
• Tclsh command line parameters
• Where does Tcl output go
• Executing IOS commands from Tcl shell
• IOS scripting with Tcl (IOS 12.3T documentation)
• TCL'ing your Cisco router

And last but not least, if you want to store Tcl procedures on your router and don't want to write into the router's Flash memory (I hate that the router prompts me whether I want to erase the flash every time I store something into it), you can store them in NVRAM.

Cisco IOS allows you to configure the ip default-gateway, but most often it looks like this setting is ignored. In fact, the default gateway is only used when an IOS device does not perform IP routing (acts like an IP host), for example, when you configure a Catalyst switch for layer-2 switching ... or when you disable IP routing on a router with no ip routing configuration command. In both cases, the show ip route command (or show ip redirects on some Catalyst switches) displays the default gateway and any ICMP redirects received from directly attached routers:

In his latest Q&A post, Scott Morris mentioned an excellent Cisco article that describes routing tricks needed to implement sinkholes and remote blackholes in great details. Highly recommended reading.