Category: Access Control

Recenty, a lot of people were looking for information on the sl_def_acl access list. Here's the whole story: if you've configured IOS login enhancements on your router, the router generates an access list named sl_def_acl (unless you specify your own with the login quiet-mode access-class command) the first time it has to enter the quiet mode. This access-list is then applied to the VTY lines whenever the router enters the quiet mode and removed from the after the quiet period is over. The access list itself is left in the running configuration.

IOS has (yet another) nice "underdocumented" feature - if you don't have an enable password/secret configured on your router, you can access IOS HTTP(S) server (assuming it's enabled with the ip http server command) without any authentication whatsoever. Of course you'd never do that in a production environment, but it's nice to know you can always configure the router from a web browser if needed (see also the discussion on default passwords with Cisco SDM).

I get a lot of hits via Google from people searching for a default username on Cisco router. It's ages-old news, but there is no default username. Period. If you have to get access to a router and cannot remember the password(s), the only thing left is the password recovery mechanism ... although even that can be disabled with the no service password-recovery configuration command.

There are, however, a few things you can do if you want to relax the access to your router in a lab environment (never do it in a production network):

You could limit terminal access to a router with an access-class in line configuration command for a very long time (since, at least, IOS release 10.0). However, the access-class command only accepted standard access-lists, allowing you to restrict access solely based on source IP addresses. In the meantime, this feature quietly got upgraded to support extended access lists. In the IOS release 12.4, the command even accepts (undocumented !) named access lists.

These new features give you the ability to implement interesting policies, for example:

Cisco has in IOS release 12.3(4)T (integrated into 12.4) finally introduced features (long available in Unix and Windows) that slow down dictionary attacks on a router. On top of logging of login failures, you can also slow down the login process by delaying the router response after a login failure with the login delay seconds command.

On top of that, the you can configure the router to enter quiet mode after several login failures have been detected in specified timeframe with the login block-for seconds attempts tries within seconds configuration command.

While you wouldn't usually want non-privileged user to reload a Cisco IOS-based router, you might also not appreciate the need to give the network operator level-15 access (which includes configuration privileges) just to reload the box. The solution is the privilege configuration command. To lower the privilege level of the reload command, configure privilege exec level desired-level reload.

As I get a lot of hits from Google refering to local login, here's the whole story: Cisco IOS supports local username/password based authentication (almost) forever (it's been there even before the AAA architecture). To change from simple password-based authentication to username+password based on, use login local configuration command on console and/or VTY lines. The local usernames and passwords are defined with the username configuration command.

In a previous post, I've shown how you can log the changes in interactive user's privilege level. With the Cisco IOS Login Enhancements (introduced in IOS release 12.3(4)T, integrated in 12.4), you can also log all login successes and failures, even when using local user database (a similar functionality was previously achievable only when using central TACACS+ or RADIUS server).

The configuration commands to enable terminal access logging are login on-success log and login on-failure log. You can also specify that you want send SNMP traps in these circumstances (with the trap option) or that you only want to log every Nth attempt with the every n option.

The logging userinfo configuration command introduced in IOS release 12.3T (integrated into 12.4) starts logging of all changes in user privilege levels (as requested by enable or disable commands).

The Cisco IOS’s AAA architecture contains many handy features, including authorizing and logging every CLI command executed on the router. Unfortunately, the AAA command accounting only supports TACACS+ as the AAA transport protocol, making it unusable in RADIUS environments.

You can use Embedded Event Manager as a workaround. The following configuration commands will log every command executed on the router.