In certificate-based IPSec deployments, the router has to establish an approximately valid date and time before it can use a certificate to establish IPSec session (as most certificates were issued after March 1st 2002, which is the default initial value, they are not valid until the router has acquired an approximately correct date-and-time).

This requirement is not a problem for most router models, as they have battery-backed hardware clock that continues running even when a router is reloaded or powered down. The low-end models, though, have a problem, as they always start with the default date/time after the reload. These devices have to get their time from an NTP/SNTP server before being able to establish the IPSec session. If the (S)NTP server is only accessible across the VPN, you have a nice chicken-and-egg problem.

I've got an interesting question a while ago: Do new Cisco routers still use CBAC?

Of course they do, it's just been renamed. The marketing department has decided that Context Based Access Control (CBAC) does not sound nearly so nice as the Cisco IOS Firewall. Even the command structure hasn't changed, you still use the ip inspect commands to configure it, unless, of course, you have IOS release 12.4(6)T or newer, where you can use zone-based policy firewall configuration.

Developing Embedded Event Manager (EEM) Tcl policies is "a bit" tedious task. Usually you would edit the source file on an external workstation, then you have to download it into the router (IOS will not read EEM policy from an external source), re-register it with EEM (when you register a policy it gets copied from the source file into system:lib/tcl/eem_registered_scripts directory) and test it. To automate this process, I've written a small EEM applet that does the tedious steps automatically.

With IOS file system (IFS) introduced in IOS release 11.3AA (integrated in 12.0), IOS got the more command that displays any local or remote file that you could specify with IFS. The obvious use of the more command would be display of startup configuration (more nvram:startup-config), but you could also display built-in Tcl EEM policies (for example, more system:lib/tcl/http.tcl) or remote router configurations (for example, more tftp://host/cfg-file). But that's not all, you could even troubleshoot web servers and display HTML generated by the web server (for example, more http://192.168.0.2/index.html).

The IOS command line interface has long included unix-style pipes that you could use to limit the output generated by the show commmands. Initially, the only available filters were begin (include everything after the first regular expression match), end (stop the output at the RE match) or include (include only matching lines).

IOS release 12.3(2)T (integrated in 12.4) brought us a few new filters, among them the section filter that includes or excludes whole sections (start of section being defined by a line with no leading space). You can use this filter to focus on parts of your router configuration. For example, to display only the routing protocols configuration, use show running | section include router command.

Embedded Event Manager is a bit picky about the location of the EEM Tcl policies: although they are loaded into RAM when registered, they have to reside on the router itself. If you have a low-end router with no flash disk (I'm using 2800-series routers) or USB flash and you don't want to mess with your flash: device (to prevent accidental erasure), the only other place left is NVRAM:. Surprisingly, it works.

If you need interface counters on subinterfaces or virtual interfaces, you can emulate them with an empty policy-map, for example:

policy-map Count
 class class-default
!
interface Serial0/0/0.100 point-to-point
 service-policy input Count
 service-policy output Count

Recently I had to investigate whether Cisco Router and Security Device Manager (SDM) uses a default username/password, so I was forced to figure out how exactly the SDM works. The minimum functionality needed on an SDM-enabled router is preconfigured Ethernet interface, HTTP server and (optionally) DHCP pool.

In his excellent question, Matt reminded me of (almost prehistoric) days when static routes pointing to a connected interface (not IP next-hop) had administrative distance zero. I also remembered that we've had interesting routing problems as those static routes actually behaved like connected routes (and were redistributed into routing protocols with redistribute connected command).

IOS release 12.3T introduced an interesting concept: static routes that are used only if an object a router is tracking (for example, next-hop router) is available. Named reliable static routing, this feature allows you to constantly ping next-hop router (or any other IP address) and use the static routes only if the tested destination is reachable.

While the reliable static routes are easy to understand and configure, a careless implementation can lead to interesting routing loops or other instability problems. You'll find the needed in-depth design and implementation guidelines in my Small Site Multi-homing article (which is one of the prime applications for reliable static routing) in sections Not-so-Very-Static-Routes and End-to-End Connectivity Test.